BondKote Mastic & Filler Epoxy Coating System

$469.00

 

How about 100% bonding strength and a material that will cure in almost any environment? With its low/no VOCs you can breathe a little easier as you fill those tough holes and divots. When it comes to a bonding filler, nothing is as effective or environmentally friendly as BondKote.

Key Attributes

  • All-purpose bond agent, grout & filler
  • Cures in moist environments
  • maximum bond strength
  • Ultra Low VOCs and no foul odors
  • LOW ENVIRONMENTAL IMPACT
  • Fully cured 24-48 hours ( at 70°F)

Recommended Substrates

  • Concrete
  • Stone
  • Masonry
  • Steel
  • Stainless Steel
  • Wood Decking
  • Plywood
  • Pressboard
  • Slatboard
  • ABS Plastic
  • PVC Plastic
  • Polycarbonate Plastic

Coverage Guide

1 unit (3 gallons) of  parts  A/B mixed covers 400 to 500 sq./ft.

KoreKote Safe Resin

SafeResin™, a revolution
in coating technology.

All our coatings are super charged by SafeResin technology. Learn why SafeResin is the next level in epoxy performance.

SAFETY DATA SHEETS (SDS)

BONDKOTE HARDENER MSDSDOWNLOAD
BONDKOTE RESIN MSDSDOWNLOAD

TECHNICAL DATA SHEETS (TDS)

BONDKOTE TDSDOWNLOAD

 

PERFORMANCE

Service Temperature-67°—600°F (depending on the application)
Impact resistantYes
Water sealYes
Solvent and chemical resistantYes
Oil and gas resistantYes

LIQUID PROPERTIES

FormSemi-thick liquid
Non-dripYes
Low/no VOCsYes
Viscosityat 77°F (25°C)
 Part A 50,000 cP
/ Part B 300 cP/
Mixed 45,000 cP
Potlife15 minutes
Gel time30 minutes
Full cure time4 – 8 hours
(depending on temperature and application)
Shelf life24 months
Cure methodChemical reaction
Application temperature50° – 80°F

CURED PROPERTIES

PermeableNo
Can be painted/stainedNo
Fills gapsYes
RemovableNo
FlexibleYes
Flash Point>200°F (93°C)

MIXING & HANDLING

Number of components2
Mix ratio2:1
Application methods
Trowel tool, grout tool, putty tool, etc.

Mix batches of the material that are appropriate for the grout or filler project you are working on so that all mixed material and be placed and finished within 30 minutes. Use a trowel or putty knife to scoop material and place/spread in desired project area. When material is spread out in a thinner layer, the worklife is extended to approximately 35 minutes (do not apply in temperatures below 50°F). For detailed handling and safety instructions, please refer to the product MSDS and TDS (Technical Data Sheets). Documents can be downloaded atwww.korekote.com/download

Precautions

Avoid contact with eyes and / or skin. Wash thoroughly after handling. Provide adequate ventilation to control vapor. KEEP OUT OF THE REACH OF CHILDREN.

SUGGESTED FIRST AID

IF SWALLOWED:Rinse mouth. Do NOT induce vomiting. Call a POISON CONTROL CENTER if you feel unwell.

 

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice. Immediately call a doctor.

 

IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. Wash contaminated clothing before reuse. If skin irritation or rash occurs: Get medical attention.

 

IF INHALED: Remove person to fresh air and keep comfrotable for breathing. Immediately call a doctor.

HANDLING SAFETY

Prolonged exposure to Part A (resin) may cause allergic skin reaction on sensitive skin and possible respiratory tract irritation. Prolonged exposure to Part B (hardener) may cause an allergic skin reaction on sensitive skin.

BondKote Hardener MSDS DOWNLOAD

 

BondKote Resin MSDS DOWNLOAD

0
KoreKote BaseKote Epoxy Primer coating SystemAnti Skid Epoxy Coating Additive