BaseKote Epoxy Primer Coating System

$449.00

 

BaseKote Primer is the only primer that gives you 40% more bond strength than ordinary primers.  Imagine if your finished project lasted 40% longer? And was 40% more durable? All of that in a primer that goes on easy, cleans up easier and has no VOCs . Now that’s peace of mind.

NOTE: 1 unit (3 gallons) covers a max of 534 sq./ft

Key Attributes

  • Base layer coat for concrete & steel
  • Strengths concrete substrate
  • Protects steel substrate from rust
  • Hydro static pressure barrier
  • Cures in damp environments
  • maximum bond strength
  • Ultra Low VOCs or foul odors
  • Mildew inhibiting
  • Self leveling for easier application
  • Low environmental impact
  • Non-permeable surface
  • Fully cured 24-48 hours ( at 70°F)

Recommended Substrates

  • Concrete
  • Stone
  • Masonry
  • Steel
  • Stainless Steel
  • Wood Decking
  • Plywood
  • Pressboard
  • Slatboard

Coverage Guide

1 Unit (3 Gallons) of Part A/B mixed covers a max of 500 sq/ft.
Mil thickness will vary depending on the substrate type and condition. (i.e. If porous concrete then material will be mostly absorbed, if steel then mil thickness will be heavier)

KoreKote Safe Resin

SafeResin™, a revolution
in coating technology.

All our coatings are super charged by SafeResin technology. Learn why SafeResin is the next level in epoxy performance.

SAFETY DATA SHEETS (SDS)

BASEKOTE HARDENER SDSDOWNLOAD
BASEKOTE RESIN SDSDOWNLOAD

TECHNICAL DATA SHEETS (TDS)

BASEKOTE TDSDOWNLOAD

 

PERFORMANCE

Impact resistantYes
Water sealYes
Solvent and chemical resistantYes
Oil and gas resistantYes

LIQUID PROPERTIES

Formsemi-thick liquid
Non-dripNo
Low/no VOCsYes
Viscosityat 77°F (25°C)
 Part A 400 cP
/ Part B 300 cP/
Mixed 345 cP
Potlife20 minutes
Gel time40 minutes
Full cure time24 – 48 hours
(depending on temperature and application)
Shelf life24 months
Cure methodChemical reaction
Application temperature50° – 80°F

CURED PROPERTIES

FinishApplies white and cures clear
PermeableNo
Can be painted/stainedNo
Fills gapsYes
RemovableNo
FlexibleYes
Flash Point>200°F (93°C)

MIXING & HANDLING

Number of components2
Mix ratio1:1
Application methods
Roller, brush, machine sprayer

1. Surface Preparation

clean surfaces to remove all dust, dirt and grease. For highest bond strength, chemical cleaning is required (use KoreKote Surface Cleaner®)

2. Mixing

Mix 1:1 ratio by volume of Part A (resin) and Part B (hardener) together. Mix thoroughly until uniform color and consistency throughout. Mechanical Stir Stick (drill with mixing paddle) is recommended.

3. Potlife

Potlife of mixed coating is approximately 20 minutes at 70˚F if material is left as a unit in mixing container. Higher temperatures reduce potlife and accelerate curing. CAUTION: Mixing large quantities (more than a 3 gallon batch size) generates significant heat and shortens potlife.

4. Application

Begin by pouring mixed material in a straight line 2 – 3 feet from the desired starting edge of the area being coated. Use lint free 3/8” nap roller on roller frame and spread material evenly over surface. Use brush to do cut-ins along edges and corners if necessary. When material is spread out in a thinner layer, the worklife is extended to approximately 35 minutes (do not apply in temperatures below 50°F).

5. Curing

Allow coating to cure at 50˚F or higher.

6. Curing profile at 70°F

  • Gel time: 40 minutes
  • Crystallized: 4 hours
  • Cured: 24 – 48 hours (depending on temperature and application)

7. Cleanup

Use denatured alcohol (not necessary to use harmful/toxic solvents) to cleanup uncured material and tools.

Precautions

Avoid contact with eyes and / or skin. Wash thoroughly after handling. Provide adequate ventilation to control vapor. KEEP OUT OF THE REACH OF CHILDREN.

SUGGESTED FIRST AID

IF SWALLOWED:Rinse mouth. Do NOT induce vomiting. Call a POISON CONTROL CENTER if you feel unwell.

 

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice. Immediately call a doctor.

 

IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. Wash contaminated clothing before reuse. If skin irritation or rash occurs: Get medical attention.

 

IF INHALED: Remove person to fresh air and keep comfrotable for breathing. Immediately call a doctor.

HANDLING SAFETY

Prolonged exposure to Part A (resin) may cause allergic skin reaction on sensitive skin and possible respiratory tract irritation. Prolonged exposure to Part B (hardener) may cause an allergic skin reaction on sensitive skin.

BaseKote Hardener SDS DOWNLOAD

 

BaseKote Resin SDS DOWNLOAD

0
KoreKote ShieldKote General Purpose Epoxy coating SystemKoreKote BondKote Mastic & Filler Epoxy coating System